Skip to content
View in the app

A better way to browse. Learn more.

Dry Dock Modeler

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Welcome to Dry Dock Modeler

HMS Mercury 1779 by All Mod Cons - Scale 1:64

Featured Replies

Hi All

This is my first attempt at a scratch build and was an in progress build log on MSW before things went missing.

Previous builds were, in order

Artesania Latina - Virginia 1819

Caldercraft - Endeavour

Caldercraft - Mary Rose

After completing the Mary Rose I wanted to challenge myself a little and decided to try my hand at a scratch build....but I also had to acknowledge my limited ability and I know I could not take sheer plans, body plans etc and construct anything that resembled a ship. I'm also not yet in the position to tackle an Ancre monograph. or Ed T's Naiad (although I do have both stashed away for later) I therefore elected to try my hand at converting a paper model that came with all the templates required and to try and make it out of wood.

After some research and in keeping with my preferred period I landed on HMS Mercury by Shipyard Paper Models

page1.jpg

example of the templates that come with the paper kit and the instructions provided

Mercury instructions.pngRigging.pngtemplate examples.jpgbulkheads template.jpg

Before we go too much further, this is not one for the purists. I'm not sure how representative the plans are of the Mercury and I'm not sure that would matter too much in any case by the time I've finished with it.....but it will have the name Mercury on the stern.

And just before I start....this will not be a faithful representation of what was on MSW as I did not keep a record of what I'd posted but I will try and capture the historical as best I can and will then provide more detail once I've caught up to where I actually am.....build commenced 8th January 2024.

First order of the day was to scan the pages of the model and resize from 1:96 to 1:64.

Once this was done the bulkheads were cut out of 6mm ply (I had to extend the height to cater for the bulwarks as these are handled differently in the paper model) and the "false keel" out of 3mm ply. The ply was standard diy stuff and is not the best, next time I'll get some airplane ply or similar

IMG_20240117_171345.jpgbulkhead extensions.jpgfalse keel.jpg

From the beakhead template the parts were broken into the component parts and glue back together 🙄 using 6mm cherry and blackened pva glue with black acrylic paint

beakhead template.jpgbeakhead parts.jpgbeakhead cut out.jpg

beakhead assembled.jpg

Beakhead and keel fitted to "false keel"

keel fitted1.jpgkeelfitted2.jpg

The 6mm cherry keel and beakhead were centered on the 3mm false keel to give a 1.5mm "rabbet" for the first planking of 1.5mm strips. Difficult to see on the pictures but I also cut a 1mm line in the keel and beakhead that could be cut out later to form the rabbet for the final planking of 1mm cherry planking.

Bulkheads were then fitted

bulkhaeds fitted.jpg

Will post more later

Thanks for looking in

Mark

  • Author

Hi All

Thanks for the likes....this will be a quick post to finalise the bulkhead work.

Once the bulkheads are installed I generally add spacers to ensure that the spacing of bulkheads are equal on both sides to keep everything aligned. This is achieved by by measuring the distance to the preceding bulkhead on both sides and averaging the distance. Two spacers are then made according to this averaged measurement and glued to the bulkheads either side of the spine

Bulkhead spacers.jpg

At this stage the structure is still flimsy as I've only used 3mm ply for the spine and this is supporting quite a lot of 6mm bulkheads.

If you look in the photo above you'll note horizontal slits cut into the bulkheads, the location of these was marked on the bulkhead templates as there is a requirement in the card model to add bracing (you'll see these in the very first post showing the examples of templates) due to the thin nature of card.

From the card model instructions you'll see the bracing installed within the bulkheads (below)

card braces.jpg

I'd already allowed to follow this process to add the strengthening as I knew the 3mm spine would not be sufficient.

Photos below show an example of one of the braces cut from 3mm ply and installed within the bulkheads. The braces were cut smaller than required for easier install and this resulted in a gap in the edge of the bulkhead, these were filled with a plug of pine and sanded flush to the bulkhead edge.

Braces cut.jpgbraces installed.jpgBulkhead plugs.jpg

The final structure is now rock solid and straight

Final top view.jpg

Thanks for dropping by

Mark

Rabbet.jpg

IMG_20240126_161000.jpg

Edited by All Mod Cons
photos included in error and have been removed

  • Author

Hi All

Thanks for the likes....

More work on the hull....I'm not sure if I'm going to explain this well enough as I've lost some of the historical photos but I'll give it a go.

The following is work on the transom area.

The paper model shows to construct out of card as below and I've shown the main templates to achieve this with H1-H4 being framing and G being the transom

transom shipyard.jpgtransom parts shipyard.jpg

Whilst this is ok for card, I need something a bit more substantial and I also need to add the height and angle of the bulwarks. There is sufficient information in the templates, it just means cutting and combining in some instances to make a new template and looking at what's provided to fashion suitable pieces.

Making the transom...using part G (top right image above). This is ok in plan but the transom is curved, to get this I had to use the markings provided on the last bulk head

last transom.jpg

The disjointed lines running left to right are the transom location and you can see this is curved. I created the curve by joining the lines and from this a template could be made. By gluing part G and this new template to sides of a block of wood it was matter of sanding to get the right profile. I also chamfered the edge to give a good face for the planking to be glued to. Apologies but the best photo I can locate is below.

The vertical marks on the above indicate where the frames are to be located and these were transferred to the bulkhead for frame positioning

IMG_20240217_170745.jpg

I made the transom 5mm thick and that required amending parts H1 to H4 for the frames and this was achieved by cutting 5mm from the templates

frames cut.jpg

This then provided the templates for framing below the transom shown below these were then filled with filler blocks using Jelutong. From memory I think I used 3mm mdf for the framing pieces

IMG_20240224_131732.jpgIMG_20240224_143849.jpgIMG_20240222_171234.jpg

The blue vertical lines you can see on the bulkhead are those mentioned above that were transferred from the bulkhead template.

The transom was also notched so that it could fit over the spine in a single piece

Above the transom was a little more tricky.....but more on that next time 🙂

Thanks for looking in

Mark

  • Author

Hi All

Carrying on with the counter timbers....

The paper model gives the following template for the bulwarks which simply glues to the hull at the deck level

bulwark template.jpgbulwarks.jpg

From this I can ascertain the angle of the counter timbers and the deck level and how this matches to the frame templates H1-H4 (also shown in the previous post)

template1.jpg

I then used this to create the pieces required from where I'd cut the paper template for the transom and matching the curves to that for the bulwark. Four blanks were lightly glued together and shaped. I elected to only use four as this will be sufficient to get the curve of the counter. The curve is achieved by shortening the length to fit the curve of the transom

counter.jpg IMG_20240221_174144.jpg

The outer frames are glued in place with a bit of packing on the side so that I can sand to get a good run of planking. The middle counter timbers will be left until the planking is finished....I find it easier to glue planks to the transom without having anything in the way.

IMG_20240225_145402.jpg

Thanks for dropping by

Mark

  • Author

Hi All

Just a quick post to finish of the hull works before planking...

At the bow I generally make my own templates for making filler blocks but there are templates provided in the paper model. I've taken these and extended the height for planking and filled the spaces with Jelutong and sanded to shape. Closer to the stem piece I added some 6mm

Screenshot 2026-08-16 172129.jpgIMG_20240216_153852.jpg

IMG_20240217_102825.jpgIMG_20240217_160734.jpg

Also added were some mast steps to better seat the masts later. Temporary battens were attached to keep the bulwark framing a little protected whilst the boat is upside down for planking

IMG_20240407_170809.jpg

Thanks for looking in

Mark

Amazing build….

Phil.

Current Ship Build: Vanguard Models HM Sherbourne - 1/64

Completed Ship Build: Italeri Elco PT Boat - 1/35

Other current builds: FAMO - Schwerer Zugkraftwagen 18T Sd.Kfz.9 with Sd.Ah.116 heavy trailer - 1/35

  • 2 weeks later...
  • Author

Hi All

Thanks for the likes. Now that the framing is complete, the planking can commence....Firstly I taped the bulwarks where I didn't want the planks glued as I'll be removing the formers once planking is complete.

First planking is hoop pine milled to 1.5mm by 5mm. Hoop pine is a pine that is straight grained and is ideal for planking as it bends quite easily when heated etc

1st layer bulwarks.jpg 1st layer planking complete.jpg

Gun ports were marked using the templates provided. This took a fair amount of time as everything really hinges around getting these placed correctly not only for the gun ports but for the channels, steps and all the other fittings on the hull. As there are no plans to take measurements from it took a lot of back and forth with the templates port and starboard to ensure everything was aligned and as symmetrical as I could get it.

An example of the templates is shown below

template1.jpg template2.jpg

Gun ports cut out, with first planking I use small brass pins hammered half way and then removed once the glue is dry

IMG_20240511_143208.jpg

To frame the gun ports I made a tube of 1mm cherry and sliced the the required length. This was achieved by making a former to the correct size, covering with cling film and planking around it . In hindsight (if I use this method again) I'd use 2mm stock rather than the 1mm to aid in planking upto/around the gunports on the second layer of planking.

Left photo shows the former followed by the tube that was formed and a gunport frame sliced off and installed

gun port former.jpg gun port.jpg gun ports installed.jpg

Normally once the first planking is complete, I'd form several bands for the second planking by working out the number of strakes required etc. However bands of planking that would be glued to the hull of the paper model are provided so I elected to use these to form the planking bands . For illustration I taped these to the hull so that you can visualise this.

showing bands.jpg

For the second planking I used 4mm x 1mm cherry

planking 4.jpgplanking 1.jpgplanking 3.jpg

I used a 4 butt shift pattern...but I think I see an error in the middle picture☹️, never mind.....

For the second planking, once shaped and edge bent etc, I use wood glue and then use a small travel iron to "iron" the plank in place....the heat from the iron sets the glue really quickly and negates the need for any clamping. I made a small "push tool" out of hard wood that I use when "ironing" to push the plank that's being glued up tight against the plank above/blow.....

this is what it looks like in cross section...and not to scale 😄....

Screenshot 2026-08-25 181517.jpg

if I locate it in the mess of the workshop I'll post a picture if there is any interest

Thanks for dropping by

Mark

  • Author

Hi All

Thanks for the likes....really appreciated

Looking back at the previous post I realise I missed providing some information on the gun ports.

Once I'd marked the gun ports on the first planking I wanted to ensure that I wasn't going to run into any problems when trying to fit the cannons through the gun port.

This was achieved by placing a piece of wood the thickness of the final deck planking, a quick mock up of a cannon and using magnets to check levels. In the picture below you can see the magnet on the inside, the outer magnet was placed in the centre of the marked gunport on the outer planking allowing me to check for issues prior to cutting out the gun ports

IMG_20240504_161713.jpg

With that ascertained I made up the false deck out of 0.8mm ply and installed in two halves (down the centre line) and pinned and glued to the frames below

IMG_20240511_172712.jpg

Once the second planking was complete I turned my attention to the deck planking....

The paper model has no allowance for a waterway but was was made out some Tasmanian Myrtle...this is what I've chosen to plank the inner bulwarks with...they'll not be painted

The 2mm stock was milled using a round nosed bit and glued to the false deck

Waterway1.pngWaterway2.jpg

waterway3.jpg

The Spirketting will be added later

The deck planking is 4mm x 1mm Tulip wood (poplar) and using a 4 butt shift pattern. I don't think this is historically accurate but I prefer this pattern. Edges of the planking are darkened with a charcoal pencil. It still needs sanding etc but there is too much other work to do that will foul the deck to put too much effort into the finish at this time

Deck.jpgdeck with waterway.jpg

Thanks for looking in

Mark

  • Author

Once the deck was semi complete I moved onto the wales. The paper model provides parts that would simply be glued onto card stock and then glued to the hull.

template.png

I used these to make the individual wale planks by sticking them to carbon paper and tracing over onto some Alder that I'd milled down to 1.5mm

carbon.jpg traced.jpg

The parts were numbered and then cut out individually and glued to the hull

in progress.jpg IMG_20250104_104832.jpg

Once finished they were sanded slightly and cleaned up to get rid of the marks left by the carbon paper

finished not stained.jpg

IMG_20250121_173237.jpg

The wales were then stained black rather than painted as i wanted to try and keep as much definition of the hook joints as possible and feared that how I paint would obscure the look and just look like a band of black

stained.jpg

Thanks for looking in and following along

Mark

  • Author

Hi All

Thanks for the likes and comments.....

This post brings us up to a period between February and April 2025 and focuses on the stern area..

The paper model gives the following graphic and refers the builder to the respective paper parts

Look.png

and this is the look (to a certain extent) that I'll be trying to represent as I won't be doing some of the artwork.

First thing was to make the main piece....because I've used double planking the model is wider than the paper version and knew this was going to be the case as i made a conscious decision at the start not to amend the bulkheads to care of this extra width.

To achieve the shape required i printed two of the parts and slid one behind the other to the the positions required....you'll also note the inner counter frames have been added now that the planking has been completed

template behind.png

From this I marked and cut out the shape from some 1.5mm cherry allowing for the placement of the windows to take into account the built width and drilled out the windows

marked out.jpg drilled out.jpg

At this point i added the fascia and cleaned up the window openings and drilled out the chase ports. To make the facia i repurposed the templates used to create the main piece

fasciaa template.pngfascia added with chase port.jpg

To replicate the columns between the windows, I made the pedestals and capitals by scraping a channel along a piece of poplar, created a simple jig to cut the angles and drilled an offset hole to create a more "pedestally" look

scraped channel.jpgjig to cut angles.jpgdrilled hole offset.jpg

These were then glued in position. To determine the column height and angle I used some masking tape between the pedestal and capital and marked the crease made

marking column height and angle.jpg

The tape was then stuck to a piece of polar at the correct width and to get the definition in the columns I milled three grooves along the length and installed

Column fit.jpg

I've lost the photos from the original MSW log about making the windows so I'll try and explain as best i can.....the outer window frames were made from 1mm x2mm cherry with the 2mm going back int the ship. This allowed me to set back the inner frames made by 1.0mm x 0.5mm cherry. This was all done piece by piece and hopefully the photo below shows better than the ones above, this is not the actual one used (but that's a whole other story ☹️). The backing is simply black card glued into place.

1788510141469.jpg

The small inner arches were made by bending the 1.0mm x 0.5mm over a drill bit placed in a soldering iron

drill bit.jpg result.jpg

Chase ports were created by making a dowel to the correct size and then milling out the unwanted inner

Quarter Deck Chase Port.jpg

Rails were added and the lettering "MERCURY" was simply printed on paper as close to a yellow ochre colour as i could get, cut out and painted yellow ochre and placed in position (not the greatest look)....but there can be no doubt now, this is actually confirmed as a replica model of HMS Mercury....it says so on the back 🙂

Photo's below show how it was left in April 2025, a bit difficult to see but clear pva glue was used in the windows to replicate glass ....next post will be the galleries

rearview1.jpg

reareview2.jpg

rearview3.jpg

Thanks for dropping by

Mark

drilled hole offset.jpg

  • 3 weeks later...
  • Author

Hi All

Looking at my photos, it looks as if I got a bit ahead of myself in the previous post. I completed the galleries before the stern work....

Previous kit models I'd completed didn't have quarter galleries so I was a little unsure on how to tackle these to start with.

Using the paper template for the bulwarks shows the placement of the formers. Left picture shows the placement, middle is the paper templates for the formers and right shows the thickness of card required if one was building out of paper

placement.jpg former pieces.jpg placement2.jpg

Using the information provided I marked the hull for the former positions and cut them out of some stock, I think it was 3mm (ish)

Placement3.jpg

For the window openings I used the template (147p below) but modified slightly to ensure fit, this was made out of 1mm Alder

Window openings.png window frame1.jpg window frame2.jpg

and installed, if you look closely you'll note battens behind the windows piece and these are there so that i could install a deeper outer frame to set the inner window frames back

window frame installed.jpg

Next stage was to fill the gaps to allow for the planking. For this I used Jelutong as it sands easily but is also quite a solid wood. I used the same process that I use if making filler blocks for the bow and this is essentially taking an oversized block of wood the requisite thickness and placing between the formers. A line is then drawn on the block tracing the the shape of the top and bottom formers onto the block whilst in-situ.. You then have the lines to sand to top and bottom and the majority of this can be completed off the model with only fine tuning required once glued into place.

planking formers.jpg

Planking and external window frames were completed next

framing.jpg

Windows were then made and glued into place, they're not perfect and the camera seems to make them look even worse than what they are (honest 😊)

side.jpg bottom.jpg

This is currently as it stands at time of posting, still some work to do

IMG_20260920_172644.jpg

Thanks for dropping by

Mark

  • 2 weeks later...

I had a few years ago a similar idea. I bought the 1/72 Entrpise drawings and bulkhead set, but never realized the project. It‘s nice to follow your build.

Regards Christian
in the shipyard: Hayling Hoy, 1759 - scale 1/36
on the drawing board: English Ship Sloops Fly, 1776; Comet,1783; Aetna, 1776; Granado, 1742; HM Cutter Alert, 1777; HMS Triton, 1771
"Have no fear of perfection - you'll never reach it." Salvador Dali

  • Author
2 hours ago, AnobiumPunctatum said:

I had a few years ago a similar idea. I bought the 1/72 Entrpise drawings and bulkhead set, but never realized the project. It‘s nice to follow your build.

Thanks Christian, good to have you following along.

Mark

  • 2 weeks later...
  • Author

Hi All

Thanks for likes.....

It's been a while since my last post in my attempts to get the build log up to date. This post is a bit out of sequence as I'd alraedy completed this prior to my post on the quarter galleries.....but I thought I'd share my method of dealing with the curved elements of the rails along the side of the hull....as shown below referenced as number 9 from the AoTS Diana

diana snip.png

first step is to cut the outer diameter and this was completed on the mill with a piece of stock attached to a turntable

IMG_20251130_131931.jpgIMG_20251130_132204.jpg

material was removed to form a "tail" to tie in with the existing rail

IMG_20251130_132732.jpg

Holding this against the hull in line with the position of the upper rail gives the position of where the curve is required to sit on the lower rail and the line is marked

IMG_20251130_133722.jpg

Knowing this lower point, a hole is drilled in the blank positioned to sit on the mark of the lower rail

IMG_20251130_134358.jpgIt's a bit difficult to see but a dowel is then glued into the hole

dowel snip.png

Its then a matter of removing the material from around the dowel to get the desired shape and positioning on the hull after scraping to get the desired profile

IMG_20260314_153856.jpg

Thanks for dropping by

Mark

It’s surprising that paper model plans can also be used for wooden builds.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Recently Browsing 0

  • No registered users viewing this page.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.